FA+
Shop
Dragon Tail Commission Info
11 years ago
Dragon Tail Commission Info
Last Updated: 08/15/13
Rundown
The scale maille dragon tails I make are done with anodized aluminum woven together with aluminum rings (lighter but less durable) or stainless steel (bit heavier but more durable). Base price for a regular sized tail is $250, this is for material and construction cost, shipping is included in most instances but may require an extra cost if it exceeds my shipping amount.
Each tail is custom made based on client descriptions. Pre-made tails are not generally something I do unless prepping for a convention then I may have a couple for sale at the table.
Depending on complexity and ordering in materials tails will usually take a up to a month to complete unless my supplier is out of stock then wait times may increase.
Sizing
Default length of full size tails is roughly 35 inches from the top of the belt loop to the tip of the tail. this is generally a good length of tail for someone in the ballpark of being 5'10" it will hang an inch or two from the ground. I can alter the length at no extra cost. To measure the right tail length for you, while standing, measure from the top of your belt line to the ground while standing in a relaxed/comfortable pose. Subtract 1 inch for belt sag and then the amount of inches you would like it to be off the ground. I generally recommend about 5 inches from the ground.
[Belt To Ground] inches - 1 inch - [Desired Height From Ground] = [Tail Length]
ex: 40 inches - 1 inch - 4 inches = 35 inches
Depending on the rings I use to put the tail together it will weigh about 2lb (aluminum rings) or about 4lb (stainless steel) which gives them a good weight and momentum for sway as you walk/run around but also not too heavy so they are comfortable to wear for long periods of time.
Each tail I construct has a pair of chainmail belt loops made in a 2x wide euro 6-in-1 weave and should be worn on a sturdy belt.
Materials
As mentioned before the rings I use are aluminum and stainless steel. The scales I most used are anodized aluminum because it comes in a nice range of colors. It is a soft metal so you do need to be aware that the colored scales can scratch and wear if they rub or come into contact with an abrasive surface. Regular wear however is not a big concern.
I have access to a wider variety of scales, some at a lower variety of colors, which include: Anodized Aluminum, Bright Anodized Aluminum, Engineered Plastic, Jewelers Brass, Stainless Steel, Blackened Stainless Steel, Bronze, Copper, Titanium, Nobium
Some of these are too expensive to keep on hand but if you dont mind paying more for the materials I can order them into stock, I have yet to test most of these materials for wear and tear so I recommend staying with Anodized Aluminum, Bright Anodized Aluminum, Engineered Plastic, and Stainless Steel for now.
Design/Pattern
Tails can be constructed in multiple colors and materials to get unique looks and patterns. some of the basic patterns I offer are as follows:
Solid Single Color: These tails are as basic as it gets, one solid color across the entire tail.
Spine/Ridge: A thin line stretching down the spine of the tail in a different/contrasting color.
Belly: This is the underside of the tail, done in a contrasting color to the upper portion.
Flecked: Unique to each tail, this takes another color randomly scattered about the tails design
these designs are all able to combine with each other (aside from the solid color):
ex: spine/belly
ex: flecked/belly/spine tail
Custom: Sometimes a commissioner will request a wide range of colors and/or materials than the typical design which can incur additional costs depending on complexity. specific patterns will be done to the best of my ability and the design will be made and approved based on reference provided. Occasionally commissioners will give free reign for me to create an original piece for them which is always exciting!
Pricing
Base pricing for my tails are $250. This is for the standard full length tail made with anodized aluminum with any type of pattern. More expensive materials or complex designs will increase the price, where as significantly shortening the tail will reduce the pricing of the quote.
Shipping/delivery is included unless your cost of shipping exceeds my shipping bracket. This may add additional pricing to your overall cost.
Please ask for a quote if you would like clarification on cost to cursedwolfcommissions[at]gmail[dot]com
Commission on the project will begin after the material cost has been payed for $50 for a standard tail, afterwards I will provide pictures and make small adjustments once. The rest of payment is then required before I will ship it out to you.
Extras?
I dont have much for extras at this point in time if you have any questions or inquiries about adding additional things to the tail let me know and i will see what i can do.
Lobster Clasps: For attaching things to a tail, such as glow-sticks and or other various things. it can also be used to clip the end of your tail up to your pocket or belt loop if you do not with to have it hanging down at any given time. If desired, I can add a single clip to the tip of a tail for no charge. Additional clips elsewhere are $2 each.
Last Updated: 08/15/13
Rundown
The scale maille dragon tails I make are done with anodized aluminum woven together with aluminum rings (lighter but less durable) or stainless steel (bit heavier but more durable). Base price for a regular sized tail is $250, this is for material and construction cost, shipping is included in most instances but may require an extra cost if it exceeds my shipping amount.
Each tail is custom made based on client descriptions. Pre-made tails are not generally something I do unless prepping for a convention then I may have a couple for sale at the table.
Depending on complexity and ordering in materials tails will usually take a up to a month to complete unless my supplier is out of stock then wait times may increase.
Sizing
Default length of full size tails is roughly 35 inches from the top of the belt loop to the tip of the tail. this is generally a good length of tail for someone in the ballpark of being 5'10" it will hang an inch or two from the ground. I can alter the length at no extra cost. To measure the right tail length for you, while standing, measure from the top of your belt line to the ground while standing in a relaxed/comfortable pose. Subtract 1 inch for belt sag and then the amount of inches you would like it to be off the ground. I generally recommend about 5 inches from the ground.
[Belt To Ground] inches - 1 inch - [Desired Height From Ground] = [Tail Length]
ex: 40 inches - 1 inch - 4 inches = 35 inches
Depending on the rings I use to put the tail together it will weigh about 2lb (aluminum rings) or about 4lb (stainless steel) which gives them a good weight and momentum for sway as you walk/run around but also not too heavy so they are comfortable to wear for long periods of time.
Each tail I construct has a pair of chainmail belt loops made in a 2x wide euro 6-in-1 weave and should be worn on a sturdy belt.
Materials
As mentioned before the rings I use are aluminum and stainless steel. The scales I most used are anodized aluminum because it comes in a nice range of colors. It is a soft metal so you do need to be aware that the colored scales can scratch and wear if they rub or come into contact with an abrasive surface. Regular wear however is not a big concern.
I have access to a wider variety of scales, some at a lower variety of colors, which include: Anodized Aluminum, Bright Anodized Aluminum, Engineered Plastic, Jewelers Brass, Stainless Steel, Blackened Stainless Steel, Bronze, Copper, Titanium, Nobium
Some of these are too expensive to keep on hand but if you dont mind paying more for the materials I can order them into stock, I have yet to test most of these materials for wear and tear so I recommend staying with Anodized Aluminum, Bright Anodized Aluminum, Engineered Plastic, and Stainless Steel for now.
Design/Pattern
Tails can be constructed in multiple colors and materials to get unique looks and patterns. some of the basic patterns I offer are as follows:
Solid Single Color: These tails are as basic as it gets, one solid color across the entire tail.
Spine/Ridge: A thin line stretching down the spine of the tail in a different/contrasting color.
Belly: This is the underside of the tail, done in a contrasting color to the upper portion.
Flecked: Unique to each tail, this takes another color randomly scattered about the tails design
these designs are all able to combine with each other (aside from the solid color):
ex: spine/belly
ex: flecked/belly/spine tail
Custom: Sometimes a commissioner will request a wide range of colors and/or materials than the typical design which can incur additional costs depending on complexity. specific patterns will be done to the best of my ability and the design will be made and approved based on reference provided. Occasionally commissioners will give free reign for me to create an original piece for them which is always exciting!
Pricing
Base pricing for my tails are $250. This is for the standard full length tail made with anodized aluminum with any type of pattern. More expensive materials or complex designs will increase the price, where as significantly shortening the tail will reduce the pricing of the quote.
Shipping/delivery is included unless your cost of shipping exceeds my shipping bracket. This may add additional pricing to your overall cost.
Please ask for a quote if you would like clarification on cost to cursedwolfcommissions[at]gmail[dot]com
Commission on the project will begin after the material cost has been payed for $50 for a standard tail, afterwards I will provide pictures and make small adjustments once. The rest of payment is then required before I will ship it out to you.
Extras?
I dont have much for extras at this point in time if you have any questions or inquiries about adding additional things to the tail let me know and i will see what i can do.
Lobster Clasps: For attaching things to a tail, such as glow-sticks and or other various things. it can also be used to clip the end of your tail up to your pocket or belt loop if you do not with to have it hanging down at any given time. If desired, I can add a single clip to the tip of a tail for no charge. Additional clips elsewhere are $2 each.
