FA+
Shop
1103
Views
Views
11
Favorites
Favorites
Category
All / All
Species Unspecified / Any
Size 639 x 1280
File Size 198 kB
Report this content
More from Thawk
I hope you all had a happy Halloween!
Introducing Sasha the shiny Eevee! She's so cute and helpful! giving out treats! (Too bad some of the locals did not quite grasp the comcept of "Take one"
This was kinda rushed. Was gonna spend the night inside drawing, but then I saw a horde forming at the top of the road. I had to participate! Next door boy was thrilled at Sasha and her friends!
A slow leak and dropping temps almost took out Rena near the end, but she powered on despite a little deflation.
Lucario kept focus despite a slightly game leg.
Poor Sasha was a little sad when it was all over...
Overall was a great night gave out a good 35 treats to the little horde! =^^=
Pokemon belong to Gamefreak / Nintendo
Digimon belong to Saban Brands LLC
Introducing Sasha the shiny Eevee! She's so cute and helpful! giving out treats! (Too bad some of the locals did not quite grasp the comcept of "Take one"
This was kinda rushed. Was gonna spend the night inside drawing, but then I saw a horde forming at the top of the road. I had to participate! Next door boy was thrilled at Sasha and her friends!
A slow leak and dropping temps almost took out Rena near the end, but she powered on despite a little deflation.
Lucario kept focus despite a slightly game leg.
Poor Sasha was a little sad when it was all over...
Overall was a great night gave out a good 35 treats to the little horde! =^^=
Pokemon belong to Gamefreak / Nintendo
Digimon belong to Saban Brands LLC
Category All / All
Species Unspecified / Any
Size 639 x 1280px
File Size 198 kB
Heh, the original model I saw for this character, shall we say, was far from being anime correct... It had certain additions in various areas that would have required a mature content warning, and probably ensured she would have never seen the light of day... =^^;
Primarily speaking I redesigned her chest =^^=
Primarily speaking I redesigned her chest =^^=
The only bad part is she does have a pinhole leak. The fluff looks great, but a lot of strain on the sides. Was supposed to have her patched up by now, but the glue I ordered online vanished en route to Illinois... >Oo<
That's why she fell over in the second picture. I rolled with it, because it allowed me to pose her more easily in the end. Although, were I to redo her, I might have a small valve on the fluff part instead...
That's why she fell over in the second picture. I rolled with it, because it allowed me to pose her more easily in the end. Although, were I to redo her, I might have a small valve on the fluff part instead...
It started as a nuisance leak. two or three dayts before you could see she was losing air. Now she has problems only after a few hours. But at least that is what allowed me to find the problem. Just need the glue to resolve it...
Thanks, there will be more plots in the future! =^^=
Thanks, there will be more plots in the future! =^^=
Heh, that she is, the newest! =^^=
This is her debut, and she seemed well received! I took Mishka's design, scaled her down a tad, and then gave her different colors =^^=
Was originall gonna give her Whitewall tires for legs (A pull toy pool toy) But they couldn't seem to get the concept down, so I punted...
Coin tossing having them make me a pair of wheel and axle assemblies that I could fit under her instead. Just trying to figure out the size that might look right... Since this is a temporary retrofit, should I do a straight axle, or maybe make a sling? But that would probably drive cost up. I need to get to Corel... =^^=
This is her debut, and she seemed well received! I took Mishka's design, scaled her down a tad, and then gave her different colors =^^=
Was originall gonna give her Whitewall tires for legs (A pull toy pool toy) But they couldn't seem to get the concept down, so I punted...
Coin tossing having them make me a pair of wheel and axle assemblies that I could fit under her instead. Just trying to figure out the size that might look right... Since this is a temporary retrofit, should I do a straight axle, or maybe make a sling? But that would probably drive cost up. I need to get to Corel... =^^=
Comments